Duval Messien proposes all the accessories for elevation masts and fixings for its air terminals. 

TUBULAR MASTS

Stainless steel tubular masts nestable by length of 2 meters and are used for air terminal support.

*Direct fixing with SAT3 / Add MANG2-16/34 coupling for SATELIT+G2

**2 fixings are necessary to install an air terminal on a mast from 2 to 4 meters

 3 fixings are necessary to install an air terminal from 5 to 6 meters

***Guying kit is necessary

DESIGNATION :

                                        REFERENCE

Threaded stainless steel nesting mast * 1 x Ø34

MAT342NIF

Stainless steel nesting masts 4m 2x2M** 2 x Ø34

MIEMB4S3N

Stainless steel nesting masts 6m 3x2M** 2x Ø34 / 1 x Ø42

MIEMB6S3N

Stainless steel masts 8m (4 x 2M)***

MIEMB8S3N

     

MASTS FIXINGS

Fixing brackets are used for air terminals installation alone or equipped with masts. 

Guying kit is used to  reinforce  the wind resistance of an air terminal installed on an elevation mast and installed on the roof of a building with a horizontal plate (PLATMAT34 or PLATMAT42) sold separately.
/!\ BE CAREFUL : when the metallical wires are used, it should be connected to the down conductors at the level of ground anchor points using standardized conductors.
The plates are constituted of a plate and a receiver tube welded for the fixing of a mast of Ø 34 mm by bolting on terrace roof. Fixing by bolting or chemical sealing. Screws no provided

Three feet saddle is used for air terminal installation on a flat or inclined roof. Provide a fixing if necessary by 3 M10  studs on slabs.

Wind withstand (*) : When the installation is only done on the roof, the three feet saddle should be ballasted with slabs. The weight of the slabs per foot is mentionned in the hereunder table regarding to the wind area and the installation configuration. This table corresponds to the hereunder three feet saddle configuration (RT =2 m and HT = 0.8m) and to a site with height H=10m

 

DESIGNATION :

                                            REFERENCE

Vertical bolting bracket – offset 200MM

ATTVMAT200

Vertical bolting bracket – offset 300MM  

ATTVMAT300

Mural fixing for mast – offset 200MM

 

FIXMATD200

Mural fixing for mast – offset 400 MM

 

FIXMATD400

Mural fixing for mast -offset 500 MM

FIXMATD500

Tie-down strapping chimney (set of 2) with 5M strip

CERCLCHEM

Horizontal plate for mast (Diam. 34mm) 

PLATMAT34

Horizontal plate for mast (Diam. 42mm) 

PLATMAT42

Offset collar in X 

Offset collar in cross X 

COLLRMATX

COLLRMATC

Guying kit – 3 points for mast (Diam. 42mm max) 

HAUBKIT3P

Guying kit – 4 points for mast (Diam. 42mm max)

HAUBKIT4P

Three feet saddle with ballast for mast (Diam. 50mm max)

TREPIED

Additional ballast for three feet saddle

DMDALETTE

     

 FIXINGS OF THE CONDUCTOR ON THE MASTS

These collars are designed for maintaining the down conductors at the elevation masts level and on all type of cylindrical elements.

DESIGNATION :

                                                                                   REFERENCE

Clamping collar – Stainless steel – Length 360mm

COLSER360

Clamping collar – Stainless steel – Length 520mm

COLSER520

Clamping collar – Stainless steel – Length 838mm 

COLSER838

 

Duval Messien proposes all the accessories for elevation masts and fixings for its air terminals. 

TUBULAR MASTS

Stainless steel tubular masts nestable by length of 2 meters and are used for air terminal support.

*Direct fixing with SAT3 / Add MANG2-16/34 coupling for SATELIT+G2

**2 fixings are necessary to install an air terminal on a mast from 2 to 4 meters

 3 fixings are necessary to install an air terminal from 5 to 6 meters

***Guying kit is necessary

DESIGNATION :

                                        REFERENCE

Threaded stainless steel nesting mast * 1 x Ø34

MAT342NIF

Stainless steel nesting masts 4m 2x2M** 2 x Ø34

MIEMB4S3N

Stainless steel nesting masts 6m 3x2M** 2x Ø34 / 1 x Ø42

MIEMB6S3N

Stainless steel masts 8m (4 x 2M)***

MIEMB8S3N

     

MASTS FIXINGS

Fixing brackets are used for air terminals installation alone or equipped with masts. 

Guying kit is used to  reinforce  the wind resistance of an air terminal installed on an elevation mast and installed on the roof of a building with a horizontal plate (PLATMAT34 or PLATMAT42) sold separately.
/!\ BE CAREFUL : when the metallical wires are used, it should be connected to the down conductors at the level of ground anchor points using standardized conductors.
The plates are constituted of a plate and a receiver tube welded for the fixing of a mast of Ø 34 mm by bolting on terrace roof. Fixing by bolting or chemical sealing. Screws no provided

Three feet saddle is used for air terminal installation on a flat or inclined roof. Provide a fixing if necessary by 3 M10  studs on slabs.

Wind withstand (*) : When the installation is only done on the roof, the three feet saddle should be ballasted with slabs. The weight of the slabs per foot is mentionned in the hereunder table regarding to the wind area and the installation configuration. This table corresponds to the hereunder three feet saddle configuration (RT =2 m and HT = 0.8m) and to a site with height H=10m

 

DESIGNATION :

                                            REFERENCE

Vertical bolting bracket – offset 200MM

ATTVMAT200

Vertical bolting bracket – offset 300MM  

ATTVMAT300

Mural fixing for mast – offset 200MM

 

FIXMATD200

Mural fixing for mast – offset 400 MM

 

FIXMATD400

Mural fixing for mast -offset 500 MM

FIXMATD500

Tie-down strapping chimney (set of 2) with 5M strip

CERCLCHEM

Horizontal plate for mast (Diam. 34mm) 

PLATMAT34

Horizontal plate for mast (Diam. 42mm) 

PLATMAT42

Offset collar in X 

Offset collar in cross X 

COLLRMATX

COLLRMATC

Guying kit – 3 points for mast (Diam. 42mm max) 

HAUBKIT3P

Guying kit – 4 points for mast (Diam. 42mm max)

HAUBKIT4P

Three feet saddle with ballast for mast (Diam. 50mm max)

TREPIED

Additional ballast for three feet saddle

DMDALETTE

     

 FIXINGS OF THE CONDUCTOR ON THE MASTS

These collars are designed for maintaining the down conductors at the elevation masts level and on all type of cylindrical elements.

DESIGNATION :

                                                                                   REFERENCE

Clamping collar – Stainless steel – Length 360mm

COLSER360

Clamping collar – Stainless steel – Length 520mm

COLSER520

Clamping collar – Stainless steel – Length 838mm 

COLSER838

 

Share this page on