Duval Messien earthing systems accessories are designed for installing an earthing system to flow the lightning current to the earth. 

EARTH RODS 

PIQACUA1M earth rod in copper coated with a diameter of 17mm is made with semi-hard steel « soul » which rigidify the earth rod and coated with 350 µ copper by lining after adhesion treatment.

The tip allows a coupling earth rod to earth rod without any other accessories (self extensible earth rod).

To drive into the ground the earth rod without damaging technical and functional components, it is recommended using a driving head (GUIDFRAPIQ2) and a driving stud (GUIDGOUJON2), avoiding any damages on earth rod head.

This system allows to keep a permanent diameter on the whole length of the rod, to ensure a better contact with earth and to get more mechanical resistance.

The tip, in hardened steel, screwed at the end of the 1st earth rod allows the driving in, even with hard grounds.

PIQINOX1M earth rod in stainless steel with a diameter of 16mm, is extensible by element, each extremity is M10 threaded which allow to adapt by clamping the GOUJONIN10 connection screw. It is recommended to use GUIDGOUJON to avoid to damage the earth rod head. The 1st earth rod to install should be equipped with a tip POINTEACSP.

A CONPIQRUB2 clamp is installed on the head of the earth rod and allows the connection betwwen the tape and the earth rod.

DESIGNATION :

                     REFERENCE

Copper steel rods (Diam. 17mm) – Length 1M  

PIQACUA1M

Stainless steel rods (Diam. 16mm) – Length 1M  

PIQINOX1M

   
     

ACCESSORIES FOR EARTH RODS

DESIGNATION :

                     REFERENCE

 

 

   
Driving stud GUIDGOUJON2

Driving head

GUIDFRAPIQ2

Rod/Screw tape connector  

CONPIQRUB2

     

EARTH GRIDS 

GRILTER1/1 and GRILTER2/1  earth grids are constituted of a metallical lattice welded in bare copper with meshes with dimension 115 x 30 x 30 mm. They are designed for installing horizontal earthing systems on hard grounds.

DESIGNATION :

                     REFERENCE

Copper earthing grid 1X1M – Meshes 115X30X30MM 

GRILTER1/1

Copper earthing grid 2X1M – Meshes 115X30X30MM

GRILTER2/1

     

INSPECTION PITS

REGCAFIFTE and REGFTED230 inspection pits are used in the earthing systems to install a flat/round coupling to connect earthing systems. It allows the tracking of earthing system when there is only one earth rod.

 

 

DESIGNATION :

                     REFERENCE

Square cast-iron inspection pit 300X300MM

REGCAFIFTE

Cast iron inspection pit 230MM

REGFTED230

Concrete riser 40 x 40 x 40 cm with lid

REHAUSBET

Concrete riser 26 x 26 x 28,6 cm 

REHAUSSEB

     

ACCESSORIES

PLAQDMTEROR2 lightning earthing systems are designed for tracking earthing system and can be used as warning system (prevention against risks of pace voltage and contact voltage).

BAREQUI100 or BAREQUI150 equipotential bars are designed for doing an interconnection, easily accessible with the electrical network of the building. It can also be used as control junction.

SERBARLAI named also cable brass dip is designed for connecting 3 to 4 flat conductors between each other.

SELFTER ground coil is installed in serie on the equipotential bonding of two earthing systems, as close as possible to the earth of the masses (inspection pit or at the bottom of a wall).

DESIGNATION :

                     REFERENCE

Equipotential connection marker (TF/TE)

PLAQLEQUI

Triangle marker Storm 3 x 200  

PLAQDMTER0R2

Ground coil HF 

SELFTER

Copper equipotentiality bar with 2 isolating pieces 50X5MM – Length 100MM

BAREQUI100

Copper equipotentiality bar with 2 isolating pieces 50X5MM – Length 150MM

BAREQUI150

Copper aluminum bimetal plate 100X100MM 

PLAQAL/CU

Black cold bitumen EF 2/4MM – 25 KG bucket 

BITUMENOIR

Cable brass dip   SERBARLAI

GROUND TESTER

MDM20K ground tester is designed for an easy and fast measure of the earth resistance and ground resistivity. This pack includes all the necessary pieces for its use (reels, earth rods, decametre..)

 

DESIGNATION :

                     REFERENCE

Ground tester Pack 

MDM20K

     

 GROUND IMPROVING

TEREC+ allows to realize earthing systems with low resistance. 

DESIGNATION :

                     REFERENCE

TEREC+ (in bag of 10 KG) 

TEREC+SAC

TEREC+ (bucket of 20 KG) 

TEREC20

Duval Messien earthing systems accessories are designed for installing an earthing system to flow the lightning current to the earth. 

EARTH RODS 

PIQACUA1M earth rod in copper coated with a diameter of 17mm is made with semi-hard steel « soul » which rigidify the earth rod and coated with 350 µ copper by lining after adhesion treatment.

The tip allows a coupling earth rod to earth rod without any other accessories (self extensible earth rod).

To drive into the ground the earth rod without damaging technical and functional components, it is recommended using a driving head (GUIDFRAPIQ2) and a driving stud (GUIDGOUJON2), avoiding any damages on earth rod head.

This system allows to keep a permanent diameter on the whole length of the rod, to ensure a better contact with earth and to get more mechanical resistance.

The tip, in hardened steel, screwed at the end of the 1st earth rod allows the driving in, even with hard grounds.

PIQINOX1M earth rod in stainless steel with a diameter of 16mm, is extensible by element, each extremity is M10 threaded which allow to adapt by clamping the GOUJONIN10 connection screw. It is recommended to use GUIDGOUJON to avoid to damage the earth rod head. The 1st earth rod to install should be equipped with a tip POINTEACSP.

A CONPIQRUB2 clamp is installed on the head of the earth rod and allows the connection betwwen the tape and the earth rod.

DESIGNATION :

                     REFERENCE

Copper steel rods (Diam. 17mm) – Length 1M  

PIQACUA1M

Stainless steel rods (Diam. 16mm) – Length 1M  

PIQINOX1M

   
     

ACCESSORIES FOR EARTH RODS

DESIGNATION :

                     REFERENCE

 

 

   
Driving stud GUIDGOUJON2

Driving head

GUIDFRAPIQ2

Rod/Screw tape connector  

CONPIQRUB2

     

EARTH GRIDS 

GRILTER1/1 and GRILTER2/1  earth grids are constituted of a metallical lattice welded in bare copper with meshes with dimension 115 x 30 x 30 mm. They are designed for installing horizontal earthing systems on hard grounds.

DESIGNATION :

                     REFERENCE

Copper earthing grid 1X1M – Meshes 115X30X30MM 

GRILTER1/1

Copper earthing grid 2X1M – Meshes 115X30X30MM

GRILTER2/1

     

INSPECTION PITS

REGCAFIFTE and REGFTED230 inspection pits are used in the earthing systems to install a flat/round coupling to connect earthing systems. It allows the tracking of earthing system when there is only one earth rod.

 

 

DESIGNATION :

                     REFERENCE

Square cast-iron inspection pit 300X300MM

REGCAFIFTE

Cast iron inspection pit 230MM

REGFTED230

Concrete riser 40 x 40 x 40 cm with lid

REHAUSBET

Concrete riser 26 x 26 x 28,6 cm 

REHAUSSEB

     

ACCESSORIES

PLAQDMTEROR2 lightning earthing systems are designed for tracking earthing system and can be used as warning system (prevention against risks of pace voltage and contact voltage).

BAREQUI100 or BAREQUI150 equipotential bars are designed for doing an interconnection, easily accessible with the electrical network of the building. It can also be used as control junction.

SERBARLAI named also cable brass dip is designed for connecting 3 to 4 flat conductors between each other.

SELFTER ground coil is installed in serie on the equipotential bonding of two earthing systems, as close as possible to the earth of the masses (inspection pit or at the bottom of a wall).

DESIGNATION :

                     REFERENCE

Equipotential connection marker (TF/TE)

PLAQLEQUI

Triangle marker Storm 3 x 200  

PLAQDMTER0R2

Ground coil HF 

SELFTER

Copper equipotentiality bar with 2 isolating pieces 50X5MM – Length 100MM

BAREQUI100

Copper equipotentiality bar with 2 isolating pieces 50X5MM – Length 150MM

BAREQUI150

Copper aluminum bimetal plate 100X100MM 

PLAQAL/CU

Black cold bitumen EF 2/4MM – 25 KG bucket 

BITUMENOIR

Cable brass dip   SERBARLAI

GROUND TESTER

MDM20K ground tester is designed for an easy and fast measure of the earth resistance and ground resistivity. This pack includes all the necessary pieces for its use (reels, earth rods, decametre..)

 

DESIGNATION :

                     REFERENCE

Ground tester Pack 

MDM20K

     

 GROUND IMPROVING

TEREC+ allows to realize earthing systems with low resistance. 

DESIGNATION :

                     REFERENCE

TEREC+ (in bag of 10 KG) 

TEREC+SAC

TEREC+ (bucket of 20 KG) 

TEREC20

Share this page on